ARMOR DECO-100
HIGH PERFORMANCE DECORATIVE AND
WATER-REPELLENT WALL SCREED
Product Description
ARMORDECO-100 is a high performing, specially formulated pre-bagged plaster mortar. It can be used on inner and outer walls. It is easy to use, strong and binds better to its substrate. It provides an even surface on which tilling can be
done faster and efficiently.
- ARMORDECO-100 produces aesthetically nice
finish with good decorative properties, other
benefits are: - High Strength
- Crack free wall
- Faster application
- Excellent coverage
- Decorative and water repellent
- Protects against wind rain.
Surfaces must be prepared thoroughly before
commencing application. All substrates must be
structurally sound, stable, dry, and clean, with
substrate compressive strength at a minimum
25MPa and cohesive strength a minimum
1.5MPa.
Surface should also be free of coatings, oil, dirt
etc. The surface to receive ARMOR DECO-100
must be dampened with water before
application.
ARMORDECO-100 can be used for the
plastering of the following areas:
- Brick
- Stone Wall
- AAC Block / Concrete Block
- Concrete surface
ARMORDECO-100 is packed in a 20kg bag and
should be mixed as illustrated below:
- Pour 3.1 to 3.5 Liters of clean water into
container, slowly add ARMOR DECO and
continue mixing. - Mix thoroughly for a period of 3 minutes with
a slow mechanical mixer to a slurry consistency
without any powder or lumps. - Before the application of ARMORDEC-100, the
surface must be made damp (SSD) with water
to allow proper adhesion.
ARMORDECO contains cement that when in
contact with bodily fluid may cause irritation and
other allergic reaction to those predisposed. .
Safety gloves and googles should be won
when mixing or applying ARMORDECO. If
ARMOR DECO comes in contact with bodily fluid
or eyes rinse immediately with copious
Appearance: Grey or White Powder, When mixed: Grey Viscous Slurry
When Dry: Grey Film
Test Results Methods
Compressive strength 22.7Mpa at 28 days ASTM C-109
Flexural Strength 2.3mpa at 28 days ASTM-348(Modified)
Bond/Adhesion >1.5mpa ASTM-C321
Crack Bridging at >0.75mm
high temperature
Permeability 1.5 Bar positive and DIN 1048
Negative water head
Bond strength at >0.5
immersion in Water
Reaction to fire Class E
Bond strength after
application of heat source 1.5 EN 14891-A
Under ideal condition and at a thickness of
10mm-12mm one bag will cover 1.5- 2 square
metres.
ARMORKRYSTAL 500 ARMORKRYSTAL 500 should be specified for all
concrete surfaces subject to hydrostatic pressure
or water attack.
ARMORKRYSTAL meets ACI 212 classification of
Permeability Reducing Admixture for Hydrostatic
Condition (PRAH)
20kg
ARMORDECO-100 can be stored in a cool dry
place for a period of 12 months.
When still in fresh state ARMORDECO-100 can
be cleaned with copious amount of water.
However, after hardening it can only be cleaned
from equipment and tools through mechanical
means.
All recommendations, statements and technical data herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty either e x p r e s s e d or implied. User shall rely on his or her own information and tests to determine suitability of the product for the intended use and user assumes all risk and liability resulting from his or her use of
the product. Nothing contained in any supplied materials relieves the user of the obligation to read and follow the warnings and instruction for each product as set forth in the current Technical Data Sheet, product label and Safety Data Sheet prior to product use away. Armorsil Manufacturing supplies products that comply with the properties shown on the current datasheets. In the unlikely event that products supplied are proved not to comply with these properties, then we will replace the non-compliant product or refund the purchase price. Armorsil Manufacturing does not warrant or guarantee the installation of the products as it does not have control over the installation or end use of the products. Any suspected defects must be reported to Armorsil Manufacturing in writing within seven working days of being detected. Armorsil Manufacturing. Makes no warranty as to merchantability or fitness for a particular purpose and this warranty is in lieu of all other warranties express or implied. Neither seller nor Armorsil Manufacturing shall be liable to the buyer or any third person for any injury, loss or damages of any sort including remote or consequential damages, down time, or delay directly or indirectly resulting from use of or inability to use the product. . The information contained in the latest data
sheet supersedes all previously published editions. Visits to site by Armorsil personnel do not constitute supervisory responsibility. Armorsil reserves the right to alter the information contained in this datasheet without prior notice