ARMORFLO 600 EMS
HIGH PERFORMING SMOOTHENING SELFLEVELLING UNDERLAYMENT
Product Description
ARMORFLO-600 is a three part, solvent free epoxy floor coating which can be easily cleaned and has high surface hardness, mechanical and chemical resistances. It has a great appearance, dust, corrosion resistance and easy to clean. It has good anti-static properties, wear and tear resistance and Suitable for heavy duty industrial and decorative flooring. It has great resistance to chemicals, acids and solvents.
- High chemical and physical resistance
- Excellent compressive strength
- Excellent flexural and tensile strength
- Seamless dust free and easy to clean.
- Dense corrosion resistant surface
ARMORFLO 600 TOP COAT can be applied as top coat over metal and concrete surfaces in:
- Factories, warehouses
- Shopping centers
- workshops
- Aircraft hangars
- Schools and hospitals
- Pharmaceutical and food industries
- Laboratories
- Car parks
- Waste water treatment plants
Surface preparation:
New concrete and plaster must be allowed to cure for at least 28 days Weak, cracked, broken sections in old concrete floor or plaster must be repaired using Filling Compound and Grout Repair Compounds; loose and unstable floors must be reinforced with anchorage after multilayer lamination.
Surface must be primed 24 hours before application with ARMORFLO 500HD in one coat. Mixing process; please note, mixing is not to be done in parts
Add component A into a clean dry container and add component B , and stir the mixture for a period of 3minutes. using low speed (300-400 rpm) electric mixer. Avoid stirring more than necessary in order to minimize entrapped air inside the mixture. Then add component c into the mixture and stir properly
Surface Temperature:
Minimum +100C / Maximum +300C
Ambient Temperature:
Minimum +100C / Maximum +300C
Material Temperature:
It must be between +100C and +300C.
Surface Moisture Content:
Humidity rate in the concrete must be maximum 4%.
Relative Humidity:
It must be maximum 80%.
Dew Point:
Temperature of the surface to be applied must be at least 300C above the dew point.
Pour the material on the area to be resurfaced using a smoothing trowel ,because of the selfleveling property of ARMORFLO 200 the material can easily be finished as desired, spike roller will be used to eliminate entrapped air or bubbles and to give a uniform appearance. The level of thickness will also be determined by the application need, but should be achieved in one application; the mixed material can be applied at a thickness between 3mm and 20 mm. If the mix hardens, it should be disposed, please do not attempt to remix or add water to hardened mix.
Remove the excess mortar on tools with copious
amount of water; if already dry you can remove
through mechanical means. Also prolonged
contact with skin may occur as it is the case with all
cementitious based material, therefore safety
gloves and glasses should be used when working.
ARMORFLO 200 should be specified for factory floors, warehouses , hospitals etc and un derlayment for floor coverings. It is particularly
suitable for areas requiring hardwearing and durable flooring.
ARMORFLO 200 is packed in 20 kg and 25kg bags
.Store in a cold dry place. With proper storage
material can be stored and used within 12 month
Chloride content: NIL
Appearance: milky tea low viscous Liquid
Density: 1.19 g/cm3
PH Value: 7 -9
Air entrainment: < 2%
Packaging: 20L
All recommendations, statements and technical data herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty either e x p r e s s e d or implied. User shall rely on his or her own information and tests to determine suitability of the product for the intended use and user assumes all risk and liability resulting from his or her use of
the product. Nothing contained in any supplied materials relieves the user of the obligation to read and follow the warnings and instruction for each product as set forth in the current Technical Data Sheet, product label and Safety Data Sheet prior to product use away. Armorsil Manufacturing supplies products that comply with the properties shown on the current datasheets. In the unlikely event that products supplied are proved not to comply with these properties, then we will replace the non-compliant product or refund the purchase price. Armorsil Manufacturing does not warrant or guarantee the installation of the products as it does not have control over the installation or end use of the products. Any suspected defects must be reported to Armorsil Manufacturing in writing within seven working days of being detected. Armorsil Manufacturing. Makes no warranty as to merchantability or fitness for a particular purpose and this warranty is in lieu of all other warranties express or implied. Neither seller nor Armorsil Manufacturing shall be liable to the buyer or any third person for any injury, loss or damages of any sort including remote or consequential damages, down time, or delay directly or indirectly resulting from use of or inability to use the product. . The information contained in the latest data
sheet supersedes all previously published editions. Visits to site by Armorsil personnel do not constitute supervisory responsibility. Armorsil reserves the right to alter the information contained in this datasheet without prior notice
