ARMORSEALER -60
MULTIPURPOSE RESIN BASED CONCRETE AND MASONRY SEALER
Product Description
ARMORSEALER-60 is a multipurpose resinbased sealer formulated to seal concrete,masonry, brick, pavers and stucco surface. It hasimpressive water repellency effect therebyprotecting concrete from grease, oil, salt,gasoline, UV rays and other harmful chemicals.
ARMORSEALER-60 does not change the
appearance of the substrat
- Protects concrete from stain and UV impact
- Because it has Permeable film, it allows
moisture in cured concrete to evaporate - It has excellent stain proofing,
weatherproofing and dustproofing properties. - It is highly resistant against aggressive
chemicals
ARMORSEALER-60 is recommended for use in
substrate such as concrete, masonry, brick,
pavers etc
- To Seal surface of decorative concrete finish
- To seal the surface of natural stones, pavers
- To seal the surface of exposed concrete areas
- For concrete or mortar substrate requiring
- protection from stain and chemical attack
Surface Preparations:
The surface must be clean, free from loose
particles, laitance, grease, wax, dirt and all
foreign materials before application. Consult
with ARMORSIL’s Technical Department
for further assistance and technical support. Do
not use this product on non porous surfaces
such as painted areas etc.
Application:
ARMORSEALER-60 is ready to use and can be
applied with a roller, brush, or sprayer. Apply in
uniform thickness to obtain a coverage of 3-5
Sq.m per 5 litres of product.
Note that coverage will depend on the porosity
of the substrate. A second may be applied in
instances where surfaces are very porous. Clean
excess material from surface before drying.
Note that the subsequent layer of concrete must
be placed before the material dries. Note that
drying time is dependent on temperature and
weather conditions.
Do not apply if it is raining, Application in areas
prone to standing water may not yield same
result as areas not subject to standing water
ARMORSEALER-60 is specified for most
substrates requiring weatherproofing and stain
proofing.
Solids (PBW) 24% ± 1%
UV Light Very good resistance
UV Light Solvent
Recommended Film Build Approx. 40- 80 microns dry per coat
Coverage Rate Approx. 3-5 m2 per liter per coat
50 micron dry lm 28days at 25°C before testing
Alkali (1% Caustic Soda) No visual effect
Mineral Turpentine Slight softening (re-harden 8 hours)
Petrol Regular Unleaded Very slight softening
(re-harden 1 hour)
Methylated spirits Causes white discoloration
(easily removed with solvent)
Tools used in the preparation and application of
ARMORSEALER-60 must be cleaned with
solvents immediately after use. It does not
contain resin and amine and therefore not toxic.
However, do not inhale or swallow. Provide
adequate ventilation .Protect against contact
with skin and eyes. Wear rubber gloves, long
sleeve shirt, goggle and side shields. In case of
contact with eyes flush repeatedly with water
and contact physician
ARMORSEALER-60 are packed in 20kg kegs
.Store in a cold dry place. With proper storage
material can be stored and used within 12
months..
All recommendations, statements and technical data herein are based on tests we believe to be reliable and correct, but accuracy and completeness of said tests are not guaranteed and are not to be construed as a warranty either e x p r e s s e d or implied. User shall rely on his or her own information and tests to determine suitability of the product for the intended use and user assumes all risk and liability resulting from his or her use of
the product. Nothing contained in any supplied materials relieves the user of the obligation to read and follow the warnings and instruction for each product as set forth in the current Technical Data Sheet, product label and Safety Data Sheet prior to product use away. Armorsil Manufacturing supplies products that comply with the properties shown on the current datasheets. In the unlikely event that products supplied are proved not to comply with these properties, then we will replace the non-compliant product or refund the purchase price. Armorsil Manufacturing does not warrant or guarantee the installation of the products as it does not have control over the installation or end use of the products. Any suspected defects must be reported to Armorsil Manufacturing in writing within seven working days of being detected. Armorsil Manufacturing. Makes no warranty as to merchantability or fitness for a particular purpose and this warranty is in lieu of all other warranties express or implied. Neither seller nor Armorsil Manufacturing shall be liable to the buyer or any third person for any injury, loss or damages of any sort including remote or consequential damages, down time, or delay directly or indirectly resulting from use of or inability to use the product. . The information contained in the latest data
sheet supersedes all previously published editions. Visits to site by Armorsil personnel do not constitute supervisory responsibility. Armorsil reserves the right to alter the information contained in this datasheet without prior notice
